You've found the attachment you want. Before you hit checkout, there's one question worth a minute of your time: will it actually fit your rack?
It's the question the B.o.S. team hears more than any other about attachments. The good news? The answer comes down to two numbers. Once you know yours, shopping for add-ons gets a whole lot simpler.
The Two Numbers That Decide Fit
Every attachment has to match your rack on two measurements:
- Tubing size. The width of the upright, which is the vertical post your attachment slides onto.
- Hole size. The diameter of the holes running up that upright, where the pins go to lock everything down.
If both numbers on the attachment match your rack, you're set. If either one is off, keep looking.
How to Measure Your Rack
Not sure what you own? Measuring takes seconds. Check the width of one upright. If it reads 2.3" (60 mm), you have 2.3" x 2.3" (60 mm x 60 mm) tubing. If it reads 3" (76.2 mm), you have 3" x 3" (76.2 mm x 76.2 mm) tubing.
Every B.o.S. rack uses square tubing, so one width measurement tells you everything about the tubing. Then look at the holes. B.o.S. racks use one of two sizes: 5/8" or 1".
That's the full list. Two tubing sizes and two hole sizes, so there isn't much room to get lost.
The Three B.o.S. Rack Families
Each B.o.S. rack family pairs one tubing size with one hole size:
- Residential and Light Commercial racks: 2.3" x 2.3" (60 mm x 60 mm) tubing with 5/8" holes. The Residential Power Rack sits here.
- Hydra racks: 3" x 3" (76.2 mm x 76.2 mm) tubing with 5/8" holes.
- Manticore racks: 3" x 3" (76.2 mm x 76.2 mm) tubing with 1" holes.
Spot the pattern? The Hydra shares its hole size with the smaller racks and its tubing size with the Manticore. That middle spot matters once you start mixing attachments between systems.
Manticore Keyholes: Both Hole Sizes in One Upright
The Manticore has one extra feature worth knowing about. The holes on the side of its uprights use a keyhole shape that combines a 1" opening and a 5/8" opening.
So on the sides, you can mount attachments in either hole size. It's a handy bit of flexibility if your collection already spans both standards. Browse the Manticore racks to see the full system.
Can a 3"x 3" Attachment Go on a 2.3"x 2.3" Rack?
Technically, yes. B.o.S. doesn't recommend it, though, and there are two reasons why.
First, the fit is loose. A 3" x 3" attachment wraps around a 2.3" (60 mm) upright with space to spare, and that gap lets it wobble. Second, the pin hole on the attachment might not line up with the holes on your rack. If the holes don't line up, you'll have a hard time pinning the attachment in place.
A wobbly attachment you can't lock down isn't what you want on your rack. Match the attachment to your tubing size and skip the headache.
Can Hydra Attachments Go on a Manticore Rack?
Yes, and they work fine. Both systems use 3" x 3" (76.2 mm x 76.2 mm) tubing, so a Hydra attachment slides onto a Manticore upright without trouble.
You'll notice one small difference. A Hydra attachment on a Manticore rack has a little upward play, so you can lift it slightly. A Manticore attachment on the same rack doesn't move at all. In practice, that play won't affect your training. You push down on an attachment during a set, so it stays seated.
This is great news if you plan to move from Hydra racks to a Manticore setup down the road. Every attachment you already own fits the new rack, so nothing goes to waste.
Standard Safety Pins vs. Mag Pins
Here's a detail that's easy to miss. Attachments built for 5/8" holes come with standard safety pins by default. Manticore attachments come with mag pins instead, and those are nicer and easier to use.
Want that upgrade on your 5/8" gear? You can buy Magnetic Rack Attachment Pins separately and swap them in.
A Quick Checklist Before You Buy
Run through this list before any attachment goes in your cart:
- Measure your upright: 2.3" x 2.3" (60 mm x 60 mm) or 3" x 3" (76.2 mm x 76.2 mm).
- Check your hole size: 5/8" or 1".
- Confirm both numbers match the attachment.
- Skip 3" x 3" attachments on a 2.3" x 2.3" (60 mm x 60 mm) rack.
- Moving from Hydra to Manticore? Your attachments come with you.
- Want mag pins on 5/8" attachments? Add them to your order.
Find Attachments That Fit Your Rack
Whether you train on a residential rack in the garage or a full Manticore build, the same two numbers decide what fits. Know your tubing size and hole size, and you'll never end up with an attachment that rattles or won't pin.
Still unsure which attachment works with your setup? The B.o.S. support team can help you sort it out before you order.



